Tire fountains are perfect for any size outdoor space that can be placed anywhere in your garden. Tire fountains are suitable for installation according to the size of the garden. Although tire fountains are suitable for placing at the focal point of the garden, fountains are suitable for any place in the garden, depending on the size and design of the fountain. Below we will teach you how to install a Tier Water Fountain easily.
After fixing the location to install the tire fountain, it is important to install the fountain base well. Because the base of the tire fountain does not install properly, it can wear out due to wind or impact. To install the base, polish the lower part of the base with cement so that the base sits firmly. Also, increase the base’s weight by filling the fountain base’s hollow part with sand or soil. Because by doing this, if the lower part of the fountain is placed well, it will not wear out. This method is good for installing tire fountains because the fountains can easily reposition. But place the base well to prevent it from falling or to install it permanently. If you want, you can make a small pool around the tire fountain to enhance the fountain’s beauty and add to the garden’s beauty.
After installing the fountain base, install the fountain water basin from which all the fountain water flows. According to the fountain’s size, the fountain’s basin is small and big but larger than the other parts of the fountain, which can easily be understood. In the middle part of the basin, there will be space for placing the motor where the motor can place easily. Set the motor well for placement so it does not move when turned on, as this will make noise from the motor. When setting up the motor, pull the motor cable out from under the fountain basin, as everything will have to reassemble if you want to connect the cable after it’s all set up.
After installing the motor, the tire should install on top of the fountain. To install the tires, install the tires one by one from the bottom. You can assemble the tires on top of the fountain instead of separately, as it will not waste time. After assembling the tires, place the part over the fountain where the water from the fountain will come out. Due to the design of the fountains, the top is of different designs, but most tires have a pineapple design on top of the fountains. If the top is not installed correctly, the fountain will not fall into place, causing water to spill.
After all parts of the fountain installation are completed, the fountain water transport tube should be well assembled. Be careful not to spill water when connecting the tube to the motor, which will slow the water speed and reduce the water flow rate. To fit the tube well to get good quality water flow or sound.
After assembling all the parts of the fountain well, fill the fountain’s basin with water. The tire fountain basin is larger than other fountain basins, so this type of fountain requires more water. Tire fountains are used as outdoor fountains, so it is not better to use distilled water in these fountains. Fill the fountain basin with enough clean water and ensure the motor inside the fountain is submerged under the water. If the fountain’s water is low or reduced, the motor makes a sound, so it is important to have the right amount of water.
After filling the fountain with water, the motor should start. It is necessary to connect the power to the motor to start the motor. For that, it is important to keep the connection safe so that no one gets an electric shock. The tire was well placed away from the house, so the cable connection piped in underground. This will not damage the fountain wire long-term, making you less likely to get a shock.
After all the fountain parts are completely installed, the last step is to turn on the fountain. Before turning on the fountain, check all parts carefully to see if anything is missing. After turning it on, observe the fountain for any disturbances. In this case, some of the problems of fountains come to the fore, they are:
Finding a good location for setting up a tire fountain is essential. Below are the aspects to consider when installing the fountain.
If you use distilled water as fountain water, you can change the water every month. But if you use normal water, it is important to change it after one week. Outdoor fountains should clean per month or use fountain protectors to keep them algae-free.
Do not use it if there is snow in your yard. Also, freezing water can damage the motor, but the entire shower should be well covered when not in use. In this way, after the end of winter, you can use it again in a new way. If you can, remove the motor from the fountain and store it indoors to prevent mirages.
Try to keep the flow of the fountain water constant for better sound quality. Variations in water flow from fountains do not produce sound well. Old water reduces flow, so change the water. Also, if kept clean, the fountain produces good-quality sound.
A Part of Hearst Digital Media
Noarong participates in various affiliate marketing programs, which means we may get paid commissions on editorially chosen products purchased through our links to retailer sites.
